Material handling & fabrication · Anand, Gujarat
Conveying lines, tanks and steel, drawn around your plant
Conveyors of every type, tanks and vessels, structural steel and build-to-drawing job work, designed around your layout, your material and your throughput, then fabricated and installed from our works in Anand.
Pick a line
FOUR LINES · 22 STOPS
Conveyor systems
Designed around your material, your throughput and your floor plan, then built from scratch rather than cut down from a catalogue part.
Quote this lineEvery stop below is something that has to be decided before fabrication starts. We decide it with you.
Belt conveyor
Troughed and flat, fixed or portable
Roller conveyor
Gravity, driven and accumulating
Chain & slat conveyor
Hot, heavy or oily loads
Screw conveyor
Powders, grain, ash, sludge
Bucket elevator
Vertical lift, centrifugal or continuous
Telescopic conveyor
Truck and container loading
Modular plastic belt
Washdown and food handling
Inclined conveyor
Cleated, sidewall, Z-profile
Build to your drawing
Most of what leaves here is a one-off. A chute at an odd angle. A screw 2.4 m long when the catalogue stops at 2. A frame measured off a part a customer posted us in a rice sack. We re-draw it, quote it, and hold the tolerances written on the sheet.
- Formats read
- PDF · DWG · DXF · STEP
- From a sample
- Measured and re-drawn
- Fit-up
- Checked before full weld
- Before dispatch
- Assembled and trial run
- Supply
- Domestic and export crated
- Minimum order
- One piece
How a job runs through the works
EIGHT STATIONS
- 01
Enquiry
Drawing, sample or sketch received and read
- 02
Offer
Material, sizes, finish and lead time quoted
- 03
Cutting
Plate, pipe and section cut to size
- 04
Forming
Bent, rolled, pressed to profile
- 05
Welding
Fit-up, tack, full weld, grind
- 06
Finishing
Shot blast, primer, paint or galvanising
- 07
Inspection
Dimensions and weld checked against the drawing
- 08
Dispatch
Crated, marked and handed to transport or export agent
Material we work in
| Grade | Description | Typical use |
|---|---|---|
| IS 2062 | Structural mild steel | Frames, platforms, chassis |
| SS 304 | Austenitic stainless | Food, pharma, washdown |
| SS 316 | Molybdenum stainless | Chemical and coastal service |
| IS 513 | Cold rolled sheet | Guards, covers, chutes |
| ALU 6061 | Aluminium alloy | Light frames and sections |
| HDG | Hot dip galvanised | Outdoor and wet duty |
Finish
- Shot blastSA 2.5 before primer
- Red oxide primerTwo coats, brush or spray
- PU / enamel paintShade to your sample
- Powder coatOven cured, RAL shade
- Hot dip galvanisingOutsourced, bath limits apply
- Pickle & passivateStainless weld areas
Tell us where it will sit — indoor, wet, chemical, coastal — and we will specify the finish with you.
Request a quote
Scope and a rough size is enough to start. Attach a drawing and we can be far more precise.
Still waiting on real material
Nothing on this page was invented. No photos, certificates, client names or capacity figures exist yet, so these four blocks stay empty until you supply them.
Shop floor & installed job photos
Supply 8–12 images: machines, work in progress, finished jobs, dispatch
Certifications & test reports
Add any ISO, material test or weld qualification documents you hold
Client names or logos
Add only customers who have agreed to be named
Capacity figures
Shop area, crane capacity, max fabricated weight, years operating
Reach the works
In working hours somebody picks up. Outside them, send the drawing — it is read the next morning.
- Phone
- OWNER TO FILL
- OWNER TO FILL
- OWNER TO FILL
- Works address
- OWNER TO FILL